hair extensions, lace front wigs, human hair wigs, hair pieces

Wigs

How to Use the Tape for a Lace Front Wigs?

Adhesive should be released from the hair side of the lace, with Lace Release or alcohol. Spray or drip it through and wait for the bond to release before lifting the hairpiece away. Always proceed gently when removing pieces. Using a small brush with top solvent or 99% alcohol, dab at the area where the spirit gum was placed and gently pull away from the skin. Always clean your pieces before re-applying by pacing on a paper towel and dabbing at the gum to dissolve the glue. Never use anything but approved cleansers or 99% alcohol for this process. Glue only can be used as well making sure to let it stand for 5 to 10 minutes or until glue is tacky

  • 1 Clean hair and or scalp and dry. ( Exfoliate scalp for best results), cut off excess lace on unit leaving about half inch on.
  • 2 Applying scalp protector to the lace and will provide easier clean up.
  • 3 Apply red liner tape to inside of lace wig on the tracking lines..you can apply only on the temple areas and back area as you see the fit of wig.
  • 4 Using a make up sponge or small painting brush, apply 2 thin coats of glue to the tape, now applied to the tracks on the unit.
  • 5 Let stand for 5 to 10 minutes until glue is tacky.
  • 6 In the meantime, apply tape to your own head on the same positions as on the unit. Repeat step 5 on your head.
  • 7 Place the unit on your head and press firmly, adjusting it for proper fit.

BONDING INSTRUCTIONS: Another method:

  • 1. Cut desired length of track tape from roll.
  • 2. Remove shielding from track tape and put glue on tape
  • 3. Apply tape to lace front wig or hair piece along track system.
  • 4. Apply desired front tape or adhesive to front area of wig or hair piece for securing.
  • 5. Apply and secure lace front wig or hair piece to front area.
  • 6. Position lace front wig or hair piece forward over your face.
  • 7. Apply Hard Bond Adhesive to track tape (Allow 3-minutes for set-up before applying wig or hair piece.)
  • 8. Position lace front wig or hair piece over track area.
  • 9. PRESS firmly where adhesive is applied to tape for hair bonding.

REMOVING AND PREPARING LACE FRONT WIG OR HAIR PIECE FOR RE-BONDING:
Make sure the lace stretches properly to blend to skin as you attach.
Using tape only with no glueUse the following step for tape only:

  • 1 Remove sheld from one side of tape after cutting into 1 to 2 inch strips.
  • 2 Apply tape to wig or hair piece where desired.
  • 3 Remove sheld from second side of tape.
  • 4 Position wig or hair piece on head where desired.
  • 5 PRESS firmly where tape is applied to bond to scalp.

Over the bonding period time your own hair will continue growing. As your hair gets longer your wig or hair piece where bonded will loosen as your hair becomes longer. Naturally, it will become necessary to remove your wig or hair piece for cleaning and repair.
Use the following steps for removing a lace front wig or hair piece:
1 Peel up the front of lace front wig or hair piece where secured using toupee tape or adhesive.
2 Peel the wig or hair piece from the track system that is bonded to your hair.
3 Once the lace front wig or hairpiece has been removed: Cut hair in track area to 1/8" long to prepare for bonding lace front wig or hair piece once again.
Cleaning and repairing your lace front wig or hair piece should be done before re-bonding lace front wig or hair piece once again.

uni wigs

we are one of the leading wig suppliers specializing in lace front wigs, human hair wigs, synthetic wigs, hair extensions and hairpieces. Come and see our collections here http://www.uniwigs.com/

Recommended Articles